Ask a compliance question

UFM 3-270-08 25 February 2026 UNIFIED FACILITIES MANUAL (UFM) APPROVED FOR PUBLIC RELEASE, DISTRIBUTION UNLIMITED O&M MANUAL: PAVEMENT MANAGEMENT UFM 3-270-08 25 February 2026 i FOREWORD Unified Facilities Manuals (UFM) provide non-mandatory, informational guidance in support of Unified Facilities Criteria (UFC) with a specific focus on facilities operations, and maintenance. Only UFC establish enforceable requirements. UFM are For Information Only (FIO) and exist to help users understand and apply UFC requirements. The purpose of UFM is to share operational procedures, maintenance practices, and practical examples that support effective implementation of UFC criteria during operations and maintenance activities. UFM may include recommended procedures, checklists, illustrations, or explana

re section(s). The procedure involves removing the old sealant, routing the reservoir to achieve the correct shape factor, cleaning the reservoir, and placing new joint seal. See UFM 3-270-01, Chapter 12. JS-HP Joint Seal – Hot Pour Ft This work type specifically addresses replacing hot pour sealant for an entire section(s). The procedure involves removing the old sealant, routing the reservoir to achieve the correct shape factor, cleaning the reservoir, and placing new joint seal. See UFM 3-270-01, Chapter 12. UFM 3-270-08 25 February 2026 73 Code Name Application Interval (yrs.) Delta T (yrs.) Work Unit Description JS-SI Joint Seal - Silicone Ft This work type specifically addresses replacing silicone sealant for an entire section(s). The procedure involves removing the old sealant, rout

and PCI. The rest of the information in the sheet was calculated in UFM 3-270-08 25 February 2026 222 Excel as shown above. Note that negative costs or costs shown in red/parentheses indicate these applications may not be justified based on the assumptions. Figure A-67 Sample Table - Global UFM 3-270-08 25 February 2026 223 APPENDIX B GLOSSARY B-1 ACRONYMS. AASHTO American Association of State Highway and Transportation Officials AC Asphalt Concrete ACN Aircraft Classification Number AMC Air Mobility Command ASTM American Society for Testing and Materials CATCODE Category Code CBR California Bearing Ratio CFME Continuous Friction Measuring Equipment CI Condition Index CIP Common Installation Picture CPE Corrugated Polyethylene DCP Dynamic Cone Penetrometer DoD Department of Defense EA Eng

nnovative Pavement Research Foundation (IPRF) Evaluation, Design, and Construction Techniques for Airfield Concrete Pavement Used as Recycled Material for Base, 2006. • Federal Aviation Administration (FAA) Advisory Circulars and Engineering Briefs. • Transportation Research Board (TRB) Recycling Reports. UFM 3-250-07 19 February 2026 3 Key DoD documents used in preparing this manual are: • UFC 3-250-01, Pavement Design for Roads and Parking Areas • UFC 3-260-02, Pavement Design for Airfields • UFM 3-260-03, Airfield Pavement Evaluation • UFM 3-260-16, O&M Manual: Standard Practice for Airfield Pavement Condition Surveys • UFM 3-270-08, Pavement Maintenance Management • UFS 3-250-04, Standard Practice for Concrete Pavements • UFGS 32 01 16.70, Cold-Mix Reused Asphalt Paving • UFGS 32 01 16

s and government-unique criteria for typical design disciplines and building systems, as well as for accessibility, antiterrorism, security, high performance and sustainability requirements, and safety. Use this manual in addition to UFC 1-200-01 and the UFCs and government criteria referenced therein. 1-6 GLOSSARY. Appendix B contains acronyms, abbreviations, and terms. 1-7 REFERENCES. Appendix C contains a list of references used in this document. The publication date of the code or standard is not included in this document. Unless otherwise specified, the most recent edition of the referenced publication applies. UFM 3-260-16 29 May 2026 3 CHAPTER 2 CONDITION SURVEY PROCEDURES 2-1 CONDITION SURVEY PROCEDURES SUMMARY. UFM 3-270-08, Pavement Management, and UFM 3-260-03, Standard Practice