Plain English, any career field. Answers cite the AF pub + paragraph, your command's supplement, and the federal (OSHA/CFR) standard behind it — with the official PDF one click away.
Showing the controlling passages directly. (daily question limit reached — showing passages)
aded: 2026-07-20T01:55Z Check the source to verify that this is the current version before use. MIL-STD-1316F 23 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. This standard establishes specific design safety criteria for fuzes and safety and arming devices. 6.2 Acquisition Requirements. Acquisition documents should specify the following: a. MIL-STD-1316 supersedes and takes precedence over the requirements of STANAG 4187. It is noted that AOP-16 contains additional information addressing many of the requirements stated herein. 6.3 Additional criteria. Individual services may issue regulations or instructions which impose additional design safety criteria or add clarifying guidelines such as: No D
version before use. MIL-STD-331D APPENDIX D 204 standard. D8.3 INFORMATION TO BE DETERMINED D8.3.1 Armed Position. The Armed position, identified per MIL-STD-1316 to be the point at which the probability of propagation (i.e. transfer) of detonation to an explosive component(s) on the barrier side opposite that of the sensitive explosive component(s) equals .005, at a confidence level of 95%, will be determined from this test. The upper single-sided confidence level shall be used. D8.3.2 Effectiveness of the interrupter. The probability of propagation in the full out-of- line position may be calculated from the data (Note: This value must be less than 1.0x10-6 in order to comply with the safety system failure rate requirement of MIL-STD-1316 and MIL-STD-1901.). Caution should be taken to b
dges for Stores Suspension Equipment Flying Qualities of Piloted V/Stol “Aircraft Aircraft Structures, General Specification for 3 Source: https://assist.dla.mil -- Downloaded: 2026-07-20T01:53Z Check the source to verify that this is the current version before use. MIL-HDBK-244A STANDARDS MILITARY MIL-STD-129 MIL-STD-21O MIL-STD-220 MIL-STD-461 MIL-STD-462 ‘MIL-STD-704 MIL-STD-81O MIL-STD-1289 MIL-STD-1316 MIL-STD-1319 MIL-STD-1385 MIL-STD-1472 Marking for Shipping and Storage Climatic Information to DetermineDesign and Test Requirements for Military Systems and Equipment Method of Insertion Loss Measurement Electromagnetic Emission and Susceptibility Requirement for the Control of Electromagnetic Interference Electromagnetic Interference Characteristics, Measurement of Aircraft Electric
Characteristics of Subsystems and Equipment MIL-STD-464 - Electromagnetic Environmental Effects, Requirements for Systems MIL-STD-1316 - Fuze Design, Safety Criteria for MIL-STD-1377 - Effectiveness of Cable, Connector, and Weapon Enclosure Shielding and Filters in Precluding Hazards of Electromagnetic Radiation to Ordnance; Measurement (Copies of these documents are available online at: https://assist.daps.dla.mil/quicksearch/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) For copies of MIL-HDBK-235-7, see Foreword of MIL-HDBK-235-1C. 2.2.2 Other Government Documents and Publications The following Government publications form a part of this document to the extent specified herein. Source: https://assist.dla.mil -- Downloaded: 2
⚠ Unofficial. Answers come from indexed publication text and may be incomplete or out of date. Your MAJCOM/unit supplement may be stricter. Always verify against the official publication before acting, citing, or writing a finding.
New and updated AFIs, supplements, and OSHA cross-references as we index them — straight to your inbox.